Blog

iPECS eMG80 Password Reset

iPECS eMG80 web admin password reset

To reset the user, admin or maintenance level password to the default values. This
procedure has been available since software A.0Fc. To complete this you must
connect directly to the Serial port on the eMG80. This is for security reasons that this
procedure needs to be performed on-site.
The serial settings on your HyperTerminal session should be 115300 Baud, 8 data
bits, no parity, 1 stop bit, no flow control.
1. Connect your PC’s serial port to the eMG80 serial port with an appropriate
serial cable or serial converter.
2. Start a Telnet session with the settings above.
3. Press enter – you should get a similar prompt:-
iPECS eMG80 System
Version MPB/AU86M-1.0Jc JAN/15
Checksum: 0
Dsp Version: 1.6(14/02/25),(A-law)
DATE: 01/27/15
TIME: 15:40:51
SITE NAME : Test PRI
You are on COM1
ENTER PASSWORD:
4. Type the password “jannie”, and press enter to access maint> mode,:-
ENTER PASSWORD: ******
5. To clear all admin and maintenance passwords, your only option, type:- ‘web
id reset’ and press enter:-
maint> web id reset
[0] Id[Maint] Level[10]=>[3] Reset!!!
Maint Level Reset end!!!
[0] Id[Maint] Pwd[*] Level[3:User] stn[0:0:0:0:0]
[1] Id[Admin] Pwd[*] Level[4:Admin] stn[0:0:0:0:0]
Display User Info end!!!
6. Finally exit the maintenance utility by typing:- x
maint> x
DATE: 1/27/15 TIME: 15:44:50
Exiting maintanence utility…

Earlier versions of <5.5 you could simply telnet into it via the MFIM IP, but this was a security issue, so its been restricted to serial only on 5.5+ system software.

The systems default IP address is 10.10.10.2 / 255.255.255.0 so your Ethernet card should be set to 10.10.10.254 to ensure correct connectivity.

The default username is “admin” with a password of “1234”

Posted in: Blog, Technical

Leave a Comment (0) →

ERROR Non Genuine Consumable

If you replace toner cartridges, image drums or other consumables with any non-genuine ones, “Unknown Consumable detected” appears and the device stops working.

To continue printing by using non-genuine consumables

When “Unknown Consumable detected” appears on the touch panel and the device stops working, you can follow the procedure below to switch to an operable state.

Note
Once you switch to an operable state, a log of having used non-genuine consumables will be recorded in the device.

1.Turn off the device.

2.Press and hold the [Clear] button to turn it on.

3.Once “RAM CHECK 100%” appears on the touch panel, release the [Clear] button.

Posted in: Blog, Technical

Leave a Comment (0) →

Yealink Click To Dial from Chrome

I have been playing around with this for a while and i have managed to get this going. This is really just notes for me but it may have you too.

Install Chrome C2D URL

Then under options fill out the IP address and username and password (admin and admin by default)

Dial http://$phoneUsername:$phonePassword@$phoneAddres/servlet?number=$number&outgoing_uri=%account%

Hangup:  http://$phoneUsername:$phonePassword@$phoneAddres/servlet?key=X

I’m working on this plugin to clean it up a bit and remove the status as its not needed for this phone.

Posted in: Blog, Technical

Leave a Comment (1) →

Xerox Service Mode

Press and hold the 0 key for 10 seconds then simultaneously press START.
You will then be asked to enter a code. Type “6789” and Enter.

That will put you into UI Diagnostics. This will work for both machines and all Xerox machines that use the Connect Key Software.

Most will take you directly into the diagnostics screen. Some models you will be required to do the following after entering the code:

Press the Machine Status button.
Select the Tools Tab.
Scroll down to Maintenance / Diagnostics.

Posted in: Blog, Scripts

Leave a Comment (0) →

Access to this web server is disabled by default because it is controlled by basic authentication

Windows Vista, Windows 7, and Windows 8

To enable Basic authentication on the client computer, follow these steps:

  1. In Windows Vista or Windows 7, click Start, type regedit in the Start Search box, and then press Enter.

    In Windows 8, hold the Windows key (WINKEY) + F, highlight Apps in the Menu bar, type regedit in the Search box, and then press Enter.

  2. Locate and then click the following registry subkey:
    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\WebClient\Parameters
  3. On the Edit menu, point to New, and then click DWORD Value.
  4. Type BasicAuthLevel, and then press Enter.
  5. Right-click BasicAuthLevel, and then click Modify.
  6. In the Value data box, type 2, and then click OK.

    Note The mapping is as follows:
    0 – Basic authentication disabled
    1 – Basic authentication enabled for SSL connections only
    2 – Basic authentication enabled for SSL and non-SSL connections

  7. Exit Registry Editor, and then restart the computer.

For more information about how to configure the WebDAV redirector to enable Basic authentication, click the following article number to view the article in the Microsoft Knowledge Base:

841215 Error message when you try to connect to a Windows SharePoint document library: “System error 5 has occurred”
Step 2: Update the Registry on the client

Note This step is required for Office 2013 and Office 2010 applications.

On the client computer, add the BasicAuthLevel registry key and an appropriate value. To do this, follow these steps.

Important Follow the steps in this section carefully. Serious problems might occur if you modify the registry incorrectly. Before you modify it, back up the registry for restoration in case problems occur.

  1. Start Registry Editor.
    • In Windows 8, hold the Windows key (WINKEY) + F, highlight Apps in the Menu bar, type regedit in the Search box, and then press Enter. If you are prompted for an administrator password or for confirmation, type the password, or provide confirmation.
    • In Windows 7 or in Windows Vista, click Start, type regedit in the Start Search box, then press Enter. If you are prompted for an administrator password or for confirmation, type the password, or provide confirmation.
    • In Windows XP, click Start, click Run, type regedit, and then click OK.
  2. Locate and then click one of the following registry subkeys:

    For Office 2010
    HKEY_CURRENT_USER\Software\Microsoft\Office\14.0\Common\Internet
    For Office 2013
    HKEY_CURRENT_USER\Software\Microsoft\Office\15.0\Common\Internet

  3. On the Edit menu, point to New, and then click DWORD Value.
  4. Type BasicAuthLevel, and then press Enter.
  5. Right-click BasicAuthLevel, and then click Modify.
  6. In the Value data box, type 2, and then click OK.

    Note The mapping is as follows:
    0 – Basic authentication disabled
    1 – Basic authentication enabled for SSL connections only
    2 – Basic authentication enabled for SSL and for non-SSL connections

  7. Exit Registry Editor, and then restart the computer.

Posted in: Blog, Technical

Leave a Comment (0) →

Remove Tool Bar by Default on Adobe

Go to the install directory, i.e.” C:\Program Files (x86)\Adobe\Acrobat Reader DC\Reader\AcroApp\ENU”.

Create a new subfolder (I used “Disabled”).

Move 3 files from the “ENU” folder into the new “Disabled” folder: AppCenter_R.aapp & Home.aapp & Viewer.aapp.

Open a PDF and no more Tool Pane!

I originally moved just the “Viewer” file but if you clicked on “Home” or “Tools” on the toolbar you couldn’t go back to the “Document.” Moving all 3 files takes care of that issue. Like a lot of people I don’t and won’t ever use any of the tools. I just want a reader.

 

Source https://forums.adobe.com/thread/1810972

 

Posted in: Blog

Leave a Comment (0) →

Fanvil Click to Dial

I have been playing around with this for a while and i have managed to get this going. This is really just notes for me but it may have you too.

Install Chrome C2D URL

Then under options fill out the IP address and username and password (admin and admin by default)

Dial:  http://admin:admin@$phoneAddress/cgi-bin/ConfigManApp.com?key=HEADSET;key=$number;ENTER

add key=HEADSET; to the beginning if you always want it to pick up the headset.

add key=SPEAKER; to the beginning if you always want it to pick up on Speaker.

Hangup:  http://admin:admin@$phoneAddress/cgi-bin/ConfigManApp.com?key=RELEASE

I’m working on this plugin to clean it up a bit and remove the status as its not needed for this phone.

Posted in: Blog, Technical

Leave a Comment (1) →

Add Exchange mail box disabling the auto mapping in outlook.

Outlook 2010 has this cool feature that auto maps the mailboxes that you have full access to. But some times you want to have access to everyone email but not have them taking up space on your outlook.

 

This command will add full access for admin@example.com to everyone but the Admin mail box. 

Get-Mailbox -ResultSize unlimited -Filter {(RecipientTypeDetails -eq 'UserMailbox') -and (Alias -ne 'Admin')} | Add-MailboxPermission -User admin@example.com -AccessRights fullaccess -InheritanceType all -AutoMapping:$false
And This command will add admin@example.com to the accounts mailbox.
Add-MailboxPermission -Identity Accounts -User admin@example.com -AccessRight FullAccess -InheritanceType All -Automapping $false

Posted in: Blog, Technical

Leave a Comment (0) →

LibreNMS Freeswitch agent-local

I had a few issues getting the freeswitch agent-local to work. In the end the fix was simple. The FSCLI path was wrong in the /opt/librenms-agent/agent-local/freeswitch file. I found the correct path by running find / -name fs_cli and editing the FSCLI=/usr/bin/fs_cli to be correct.

 

Update: If you would like the Apache Status to work add the following to your apache config  /etc/httpd/conf/httpd.conf
ExtendedStatus On
<Location /server-status>
SetHandler server-status
Order deny,allow
Deny from all
Allow from localhost 127.0.0.1
</Location>

You can check by running /opt/librenms-agent/agent-local/apache

 

Posted in: Blog, Technical

Leave a Comment (0) →
Page 2 of 14 12345...»